{{ name }}
Article no. {{ combinedCodeWithHighlight }}
Article code:
EAN / GTIN:
Manufacturer number:
Cat. No.:
Indexable insert for milling SOMT....20ER-LD, for high feed rate indexable face mills, CA6535
Article no.: 589257
Catalog no.: 222084
Article code:
Product details
Technical Data
| Through-coolant | no | |
| Entry of cooling lubricant | without cooling lubricant entry | |
| Escape of cooling lubricant | without cooling lubricant exit | |
| Cooling lubricant | yes | |
| Wet minimum | suitable | |
| Wet maximum | suitable | |
| Manufacturer’s designation | SOMT100420ER-LD CA6535 | |
| Dry machining | suitable | |
| Oil | suitable | |
| Air | suitable | |
| Base form | square | |
| Insert width | 10.45 mm | |
| Insert version | right-hand | |
| Corner radius | 2 mm | |
| Corner chamfer length | 1 mm | |
| Corner chamfer angle | 32.7 degrees | |
| Corner angle | 90 degrees | |
| Rake angle | 0 degrees | |
| Setting angle | 14 degrees | |
| Normal clearance angle (main cutting edge) | 16 degrees | |
| Normal clearance angle (auxiliary cutting edge) | 16 degrees | |
| Normal clearance angle (flat cutting edge) | 0 degrees | |
| ISO-Code | SOMT100420-ER-LD | |
| Attachment hole diameter | 4.6 mm | |
| Type of chip breaker | L | |
| Wiper length axial | 1 mm | |
| Tool material | Carbide | |
| Machining group | K (cast iron); M (stainless steel); P (steel); S (difficult-to-machine materials) | |
| Tool application group | HOG | |
| Cutting media, manufacturer’s designation | CA6535 | |
| Coating | CVD | |
| Grade | CA6535 | |
| Insert thickness | 4.58 mm | |
| Type of fastening for insert | S (with counterbore screwed through hole) | |
| Interface coding for insert | SO1004203R | |
| Interface coding for insert according to ISO TS 13399-60 | SO1004203R | |
| Insert designation | SOMT....20ER-LD | |
| Type of product | Cutter insert | |
| With ISO code | yes | |
| Standard | DIN ISO 1832 | |
| Number of teeth | 4 pcs. | |
| Direction of action | right-hand | |
| Suitable for material | cast iron (K); heat-resistant super-alloys (S); stainless steel (M); steel (P) | |
| Tolerance Class | M | |
| Machining method | face milling (FPL) | |
| Finishing / roughing assignment | Finishing; Roughing | |
| Type of fastening | Hole | |
| Chip breaker | yes | |
| Cutter version | chamfered and rounded (S) | |
| Cutting conditions | continuous | |
| Number of potential uses | 4 pcs. | |
| Weight | 2 g | |
| Content | 10 pcs. | |
| Correction factor fz | 2.5 |
Identification & Classification
| Article number | 589257 | |
| Catalog number | 222084 | |
| EAN / GTIN | 4960664708277 | |
| Manufacturer number | TMA05608 | |
| Manufacturer/responsible person | KYOCERA UNIMERCO Tooling GmbH, Hammfelddamm 6, 41460 Neuss, Germany, www.kyocera-unimerco.de |
Application Table
S
30
Description
Version:
4-edge indexable inserts with convex cutting edges for low cutting forces.
Application:
LD geometry is also suitable for high cutting depths (ap max= 5 mm) at moderate feed rates.
Do not use for helical, plunging or contour milling, or on steep walls.
Do not use for helical, plunging or contour milling, or on steep walls.
Note:
Standard application values for ae = 0.3×D.