{{ name }}
Codice art. {{ combinedCodeWithHighlight }}
Codice materiale:
EAN / GTIN:
Codice del produttore:
Codice articolo:
ULTRACUT Viti per calcestruzzo FBS II 8x100 50/35 SK
Codice art.: 169849
N. del catalogo: 3342
Codice materiale:
Dettagli prodotto
Dati tecnici
| Ø | 18 mm | |
| Professionale / Fai da te | Profi | |
| d0 | 8 mm | |
| Ambiente | Dentro | |
| materiale | zincato a freddo | |
| Dimensione bit (TX) | 40 | |
| h2 | 110 mm | |
| Protezione superficiale | Con zincatura galvanica/elettrolitica | |
| Forma testa | Tête fraisée | |
| l | 100 mm | |
| Tipo | FBS II 8x100 50/35 SK |
Unità di imballaggio
| 1 Pacco | 50 pezzi | |
| 1 Pallet | 7800 pezzi |
Identificazione e classificazione
| Codice articolo | 169849 | |
| Numero del catalogo | 3342 | |
| EAN / GTIN | 4048962410716 | |
| Codice del produttore | 558229 | |
| Classe dell’articolo | RMN |
Descrizione
Vantaggi:
- With up to 3 embedment depths, the UltraCut FBS II US allows for the same screw to be used for different component thicknesses.
- The special saw tooth geometry enables fast cutting into the concrete.
- Drill holes do not need to be cleaned during vertical installation (ceiling and floor). For floor fixings the hole must be drilled 3x drill hole diameter deeper.
- Expansion-free anchoring (undercut) allows for lowest edge- and axial spacings.
- The ETA approval covers applications in cracked concrete and seismic power categories C1 and C2.
- The approved adjustment for the concrete screws allows the screw to be unscrewed twice to place maximum 10 mm packing below the base plate head or to align the attached part, and then to tighten the screw again.
- The checking gauge allows for reuse in temporary fixings (e.g. inclined supports) covered by the national approval.
- The concrete screw FBS II 6-10 in zinc-plated steel, multiple-coated steel CP and stainless steel R has an ETA for bricks of clay (EN771-1), solid sand-lime brick (EN771-2) and perforated sand-lime brick (EN771-2) for a flexible use in different substrates.
- The installation of the concrete screw FBS II 6-10 in zinc-plated steel, multiple-coated steel and stainless steel R in masonry brick can be made in the joints or in plastered substrates also in groups.
Area di applicazione:
- Guard rails
- Consoles/Base plates
- Metal profiles
- Reinforcement of bridges
- Rehabilitation of old and ailing buildings
- Rehabilitation of car parks
Approved for:
- Concrete C20/25 to C50/60, cracked and non-cracked
- Reinforcement of existing concrete structures
- Bricks of clay (EN771-1)
- Solid sand-lime brick (EN771-2)
- Perforated sand-lime brick (EN771-2)
- Concrete C12/15
- Solid building materials
- Masonry with a dense structure
Note applicative:
- The UltraCut FBS II is recommended for the push-through installation.
- Drill holes do not need to be cleaned during vertical installation (ceiling and floor). For floor fixings the hole must be drilled 3x drill hole diameter deeper.
- We recommend using a tangential impact screwdriver with a suitable impact screwdriver socket or an internal TX drive.
- The screw is installed correctly when the screw head sits flush on the fixture and cannot be screwed in deeper (visual setting control).