{{ name }}
Codice art. {{ combinedCodeWithHighlight }}
Codice materiale:
EAN / GTIN:
Codice del produttore:
Codice articolo:
TherMax II 12/110 M12
Codice art.: 2219649
N. del catalogo: 4930
Codice materiale:
Dettagli prodotto
Dati tecnici
| Filettatura di raccordo | M12 | |
| materiale | zincato a freddo | |
| Materiale |
acciaio
|
|
| Materiale da costruzione | Calcestruzzo | |
| Azionamento | Esagonale | |
| M | M12 | |
| Contenuto | 20 pz. | |
| e min | 110 mm | |
| Professionale / Fai da te | Profi | |
| Ambiente | Zona umida / Esterno | |
| Protezione superficiale | zincato | |
| Lungehzza totale | 240 mm | |
| Imballaggio | scatola | |
| Tipo | TherMax II; 16/170 M12 | |
| Applicazione | Tende da sole | |
| Marchi di prova / omologazioni | ETA - Valutazione Tecnica Europea |
Unità di imballaggio
| 1 Pacco | 20 pezzi |
Identificazione e classificazione
| Codice articolo | 2219649 | |
| Numero del catalogo | 4930 | |
| EAN / GTIN | 2000001183854 | |
| Codice del produttore | 575222 | |
| Classe dell’articolo | RMD |
Descrizione
Vantaggi:
- The anti-cold cone made of glass fibre reinforced plastic interrupts the thermal bridge between the fixture and the anchor in the masonry.
- The optimized geometry of the cone enables easy and precise cutting into the ETICS. This makes installation particularly easy and at the same time prevents damage to the insulation material and plaster.
- Thanks to the articulated connection between the anti-cold cone and the cover cap, angled drill holes of up to 5° can be compensated for.
- The elastic EPDM sealing ring is placed on the anti-cold cone at the end of installation. This ensures that the seal is not damaged by the plaster during installation and guarantees 100% functionality and resistance to driving rain. Additional sealing of the annular gap with an elastic sealant and adhesive is not necessary.
- With just one TherMax II, insulation thicknesses of 60 to 300 mm in concrete and up to 250 mm in perforated building materials can be covered. The threaded rod is shortened to the appropriate insulation thickness at the installation site.
- The stand-off installation system is approved in combination with a wide variety of injection mortars for high loads in a wide range of building materials.
- The anti-cold cone and threaded pin can be adjusted retrospectively without expensive special tools to ensure precise alignment. This offers maximum flexibility and is also covered by the approval.
- The parts of TherMax II that lie outside the insulation are made of stainless steel.
Fornitura:
20 x TherMax II M12 x 240
20 x Sleeve 20 x 130
5 x Bit
5 x Cutting blade
5 x Manual
20 x Sleeve 20 x 130
5 x Bit
5 x Cutting blade
5 x Manual
Area di applicazione:
Approved for:
For the thermally separated fixing of:
- Concrete, cracked and non-cracked
- Vertically perforated brick
- Hollow blocks made from lightweight concrete
- Perforated sand-lime brick
- Solid sand-lime brick
- Solid brick
- Aerated concrete
For the thermally separated fixing of:
- Awnings
- Canopies
- French balcony railings
- Air conditioning units
- Satellite dishes
Note applicative:
- The TherMax II is suitable for pre-positioned installation.
- The self-tapping, glass fibre reinforced cone cuts its own way through the plaster into the insulation during installation.
- The anti-cold cone uses a thermal barrier to minimise heat losses.
- In the case of a resistant plaster (e.g. thick cement plaster), it is recommended to use the included TherMax II cutting blade for grinding out the plaster.
- Inclined drill holes up to 5° are levelled by the separated cover cap with sealing ring in combination with the rounded head of the anti-cold cone.
- The elastic EPDM sealing ring is placed loosely on the cover cap and thus provides permanent protection against moisture and driving rain.
- The anti-cold cone and the threaded pin can be subsequently adjusted.