{{ name }}
Codice art. {{ combinedCodeWithHighlight }}
Codice materiale:
EAN / GTIN:
Codice del produttore:
Codice articolo:
Vite per calcestruzzo con testa a vite 6 60/5 (2)
Codice art.: 2242010
N. del catalogo: 8468
Codice materiale:
Dettagli prodotto
Dati tecnici
| Professionale / Fai da te | Fai da te | |
| Ambiente | Dentro | |
| Condizioni di applicazione | Dentro | |
| materiale | zincato a freddo | |
| Dimensione bit (TX) | 30 | |
| Lunghezza della vite | 60 mm | |
| Protezione superficiale | Con zincatura galvanica/elettrolitica | |
| Forma testa | Tête fraisée | |
| Imballaggio | blister | |
| Azionamento | TX30; Impronta Torx TX10 | |
| Marchi di prova / omologazioni | Classificazione del fuoco |
Identificazione e classificazione
| Codice articolo | 2242010 | |
| Numero del catalogo | 8468 | |
| EAN / GTIN | 4048962477252 | |
| Codice del produttore | 567290 | |
| Classe dell`articolo | RMN |
Descrizione
Vantaggi:
- The first concrete screw with diameter 6 and variable embedment depths enables high flexibility and a precise adaption on the loads.
- The ETA assessment option 1 includes the use in cracked and non-cracked concrete for highest safety requirements.
- The first 6 mm diameter concrete screw with an ETA assessment for the C1 seismic performance category for additional safety standards.
- The UltraCut FBS II 6 is approved for multiple use of non-load bearing systems and thereby ideal for the installation of pipe routes, cable trays and prestressed hollow concrete ceilings.
- Drill holes do not need to be cleaned during vertical installation (ceiling and floor). For floor fixings the hole must be drilled 3x drill hole diameter deeper.
- Different head designs offer a maximum of flexibility and a perfect adaptation to the application.
- The countersunk head offers a flush installation and is suitable for visually appealing installations.
- The special double angle on the under-head geometry increases the stability of the concrete screw during screwing in.
- The approved adjustment for the concrete screws allows the screw to be unscrewed twice to place maximum 10 mm packing below the base plate head or to align the attached part, and then to tighten the screw again.
- The concrete screw UltraCut FBS II 6 offers the possibility for use in masonry (solid building material).
- The concrete screw FBS II 6-10 in zinc-plated steel, multiple-coated steel CP and stainless steel R has an ETA for bricks of clay (EN771-1), solid sand-lime brick (EN771-2) and perforated sand-lime brick (EN771-2) for a flexible use in different substrates.
- The installation of the concrete screw FBS II 6-10 in zinc-plated steel, multiple-coated steel and stainless steel R in masonry brick can be made in the joints or in plastered substrates also in groups.
Fornitura:
2 x UltraCut FBS II 6 x 60/5
Area di applicazione:
Approved for:
- Concrete C20/25 to C50/60, cracked and non-cracked
- Prestressed hollow concrete ceilings C30/37 to C50/60 for the multiple use of non-load bearing systems
- Bricks of clay (EN771-1)
- Solid sand-lime brick (EN771-2)
- Perforated sand-lime brick (EN771-2)
- Concrete C12/15
- Masonry with a dense structure
- Solid building materials
- Pipeline routes
- Suspension for individual pipes
- Suspended mounting rails
- Prestressed concrete hollow core ceilings
- Cable trays
- Ventilation ducts
- Perforated tapes
Note applicative:
- The UltraCut FBS II 6 is recommended for the push-through and pre-positioned installation.
- We recommend using a tangential impact screwdriver with a suitable impact screwdriver socket or an internal TX drive.
- Drill holes do not need to be cleaned during vertical installation (ceiling and floor). For floor fixings the hole must be drilled 3x drill hole diameter deeper.
- The screw is installed correctly when the screw head sits flush on the fixture and cannot be screwed in deeper (visual setting control).