{{ name }}
Codice art. {{ combinedCodeWithHighlight }}
Codice materiale:
EAN / GTIN:
Codice del produttore:
Codice articolo:
ULTRACUT Viti per calcestruzzo FBS II 10x120 65/55/35 US R
Codice art.: 667311
N. del catalogo: 3333
Codice materiale:
Fare clic per ingrandire l‘immagine
Fare clic per ingrandire l‘immagine
Fare clic per ingrandire l‘immagine
Fare clic per ingrandire l‘immagine
Fare clic per ingrandire l‘immagine
Fare clic per ingrandire l‘immagine
Fare clic per ingrandire l‘immagine
Fare clic per ingrandire l‘immagine
Fare clic per ingrandire l‘immagine
Dettagli prodotto
Dati tecnici
| d0 | 10 mm | |
| SW | 15 mm | |
| Profondità minima di avvitamento | 55 mm | |
| materiale | acciaio inossidabile | |
| h2 | 130 mm | |
| Classe del materiale | altri | |
| Forma testa | Tête à six pans | |
| Ø | 20.5 mm | |
| Professionale / Fai da te | Profi | |
| Ambiente | Zona umida / Esterno | |
| Protezione superficiale | non trattato | |
| Imballaggio | scatola | |
| Tipo | FBS II 10x120 65/55/35 US R | |
| Spessore massimo del componente aggiuntivo | 65 mm | |
| l | 120 mm | |
| Marchi di prova / omologazioni | Classificazione del fuoco |
Packaging units
| 1 Pacco | 50 pezzi | |
| 1 Pallet | 5000 pezzi |
Identificazione e classificazione
| Codice articolo | 667311 | |
| Numero del catalogo | 3333 | |
| EAN / GTIN | 4048962308266 | |
| Codice del produttore | 543574 | |
| Classe dell`articolo | RMN |
Descrizione
Vantaggi:
- The specially hardened red tip provides a faster and more secure installation.
- The stainless steel concrete screw guarantees a high level of corrosion resistance especially for wet rooms and external applications.
- The special saw tooth geometry enables fast cutting into the concrete.
- Drill holes do not need to be cleaned during vertical installation (ceiling and floor). For floor fixings the hole must be drilled 3x drill hole diameter deeper.
- The ETA approval covers applications in cracked concrete and seismic power categories C1 and C2.
- The approved adjustment for the concrete screws allows the screw to be unscrewed twice to place maximum 10 mm packing below the base plate head or to align the attached part, and then to tighten the screw again.
- The three embedment depths, allow for using the UltraCut FBS II R in many different applications and enable a high flexibility.
- The short UltraCut FBS II R, with a reduced embedment in depth, allows for a short drill hole depth, fast installation and less reinforcement hits.
- The concrete screw FBS II 6-10 in zinc-plated steel, multiple-coated steel CP and stainless steel R has an ETA for bricks of clay (EN771-1), solid sand-lime brick (EN771-2) and perforated sand-lime brick (EN771-2) for a flexible use in different substrates.
- The installation of the concrete screw FBS II 6-10 in zinc-plated steel, multiple-coated steel and stainless steel R in masonry brick can be made in the joints or in plastered substrates also in groups.
Area di applicazione:
- Guard rails
- Consoles/Base plates
- Metal profiles
- Steel constructions
- Façades
- Protection barriers
Approved for:
- Concrete C20/25 to C50/60, cracked and non-cracked
- Bricks of clay (EN771-1) - only for diameter 8 and 10
- Solid sand-lime brick (EN771-2) - only for diameter 8 and 10
- Perforated sand-lime brick (EN771-2) - only for diameter 8 and 10
- Concrete C12/15
- Solid building materials
- Masonry with a dense structure
Note applicative:
- The UltraCut FBS II R is recommended for the push-through installation.
- Drill holes do not need to be cleaned during vertical installation (ceiling and floor). For floor fixings the hole must be drilled 3x drill hole diameter deeper.
- We recommend using a tangential impact screwdriver with a suitable impact screwdriver socket or an internal TX drive.
- The screw is installed correctly when the screw head sits flush on the fixture and cannot be screwed in deeper (visual setting control).